Multiple Choice Identify the
choice that best completes the statement or answers the question.
|
|
1.
|
The TCP/IP _____ layer defines the functionality of the upper layers, including
support for data formatting, conversion, and encryption.
a. | Internetwork | c. | Application | b. | Transport | d. | Network
Interface |
|
|
2.
|
_____ permits remote tracking and management of TCP/IP hosts.
|
|
3.
|
The _____ service provides TCP/IP host name to IP address resolution.
|
|
4.
|
Well Known TCP Port _____ is for FTP data transfer.
|
|
5.
|
Well Known UDP Port _____ is used by TFTP.
|
|
6.
|
The _____ protocol resolves IP addresses to MAC addresses for source hosts that
know the IP addresses of the destination host but not the MAC address.
|
|
7.
|
Each Class B address supports _____ hosts.
a. | 64,064 | c. | 64,256 | b. | 64,128 | d. | 65,534 |
|
|
8.
|
With _____ routing, the routers communicate with one another and create and
maintain routing tables automatically.
a. | static | c. | dynamic | b. | system | d. | network |
|
|
9.
|
_____ configuration is a manual process in which a network administrator must
type the paths from one network segment to the other.
a. | Static | c. | Dynamic | b. | System | d. | Network |
|
|
10.
|
The IEEE _____ standard defines the access method used by most Ethernet
networks.
a. | 802.2 | c. | 802.4 | b. | 802.3 | d. | 802.5 |
|
|
11.
|
_____ describes a coaxial cable network that has a 10-Mbps baseband transmission
rate over a maximum segment length of 185 meters.
a. | 10BaseT | c. | 10Base5 | b. | 10Base2 | d. | 100BaseT |
|
|
12.
|
To enter privileged EXEC, you can type the command _____ at the user mode
prompt.
a. | enter | c. | enable | b. | activate | d. | open |
|
|
13.
|
_____ configuration mode permits you to enable routing protocols such as RIP and
IGRP.
a. | Interface | c. | Router | b. | Base | d. | Virtual |
|
|
14.
|
_____ configuration mode allows you to configure the Ethernet and serial
interfaces on your router.
a. | Interface | c. | Line | b. | Base | d. | Virtual |
|
|
15.
|
With _____ configuration mode, you can configure the virtual terminals, console,
and AUX lines that let you access the router.
a. | interface | c. | line | b. | base | d. | virtual |
|
|
16.
|
If you are typing commands and you see the _____ symbol, it means that the line
is continued from a previous line.
|
|
17.
|
If you are in interface configuration mode, which router prompt will you
see?
a. | router(config)# | c. | router(config-if)# | b. | router(config-int)# | d. | router# |
|
|
18.
|
If you are at the router(config-router)# prompt and you type exit, which prompt
will you see next?
a. | router> | c. | router(config)# | b. | router# | d. | router(config-line)# |
|
|
19.
|
What does the acronym CDP stand for?
a. | Cisco Development Protocol | c. | Cisco Dynamic
Protocol | b. | Cisco Discovery Protocol | d. | Core Discovery Protocol |
|
|
20.
|
How can you determine the version of IOS your router is running?
a. | show ios | c. | show software | b. | show version | d. | show
ios-version |
|
|
21.
|
Which character will you see on your router's console with a successful
ping?
|
|
22.
|
When using the command show int s0/0, which reply indicates that there are
physical problems with the router interface?
a. | Serial0/0 is administratively down, line protocol is down | b. | Serial0/0 is up,
line protocol is administratively down | c. | Serial0/0 is down, line protocol is
down | d. | Serial0/0 is up, line protocol is down |
|
|
23.
|
RIP is a member of which type of routing protocol?
a. | Distance-link | c. | Distance-vector | b. | Link-distance | d. | Link-vector |
|
|
24.
|
Which of the following configurations will enable RIP routing for the 10.20.30.0
network?
a. | Router rip; network 10.0.0.0 | b. | Router rip 10; network 10.0.0.0
255.255.255.0 | c. | IP router rip; network 10.0.0.0 | d. | Router rip; network
192.168.3.0 | e. | Router rip; network 10.20.30.0 255.255.255.0 |
|
|
25.
|
Which of the following are advantages provided by NAT?
a. | It conserves public IP addresses. | b. | It hides your internal IP addressing scheme
from the outside world. | c. | It allows for easy renumbering of your IP
addresses. | d. | all of the above |
|
|
26.
|
How many access lists per protocol can an interface have?
|
|
27.
|
What are the number ranges for standard IP access lists?
a. | 0-99 | c. | 1-99 | b. | 0-100 | d. | 100-199 |
|
|
28.
|
Given the following:
access-list 111 deny tcp 200.1.1.0 0.0.0.255 any eq
80 access-list 111 permit ip any any interface ethernet 0 ip access-group 111
out
Which of the following statements is true?
a. | Telnet traffic coming in interface e0 will not be blocked. | b. | FTP traffic in
either direction is allowed to pass through interface e0. | c. | Outbound http
traffic on interface e0 will be filtered against an extended access-list. | d. | both a and
b | e. | a, b, and c |
|
|
29.
|
In an extended IP access list, what keyword is short for a wildcard mask of
0.0.0.0?
|
|
30.
|
Which of the following would be the correct syntax for a deny or permit
statement for a standard IP named list?
a. | RouterC(config-ext-nacl)#deny{source [source-wildcard] |
any | b. | RouterC(config-std-nacl)#deny{source [source-wildcard] |
any | c. | RouterC(config)#ip access-list extended [name] | d. | RouterC(config)#ip
access-list standard [name] |
|
|
31.
|
Which command shows only the IP access lists on a router?
a. | show access-lists | c. | show ip access-lists | b. | show ipx access-lists | d. | show interface |
|
|
32.
|
Frame Relay separates each data stream into logical connections called _____
circuits, which carry the data transferred on the connection.
a. | virtual | c. | static | b. | dedicated | d. | dynamic |
|
|
33.
|
In order to allow a single serial interface to support multiple PVCs, the IOS
divides the interface into logical _____.
a. | subunits | c. | units | b. | modules | d. | subinterfaces |
|
|
34.
|
Which Frame Relay term defines the rate at which your telco provider
'guarantees' that you can send data over an individual circuit?
a. | Burst Rate | c. | DE | b. | CIR | d. | BECN |
|
|
35.
|
In _____ communications, devices can send and receive signals, but not at the
same time.
a. | simplex | c. | full-duplex | b. | half-duplex | d. | simple |
|
|
36.
|
With VLANs, the microsegmentation of _____ traffic makes it even more difficult
to intercept useful data passed between two hosts.
a. | unicast | c. | microcast | b. | minicast | d. | all |
|
|
37.
|
Switches that utilize _____ forwarding start sending the frame immediately after
reading the destination MAC address into their buffer.
a. | cut-through | c. | fragment-free | b. | store-and-forward | d. | adaptive
cut-through |
|
|
38.
|
_____ switching represents an effort to provide more error-reducing benefits
than cut-through switching.
a. | Dynamic | c. | Fragment-free | b. | Store-and-forward | d. | Static |
|
|
39.
|
What protocol is used to prevent logical loops in a bridged network?
a. | Bridge Group Protocol | c. | Address Resolution Protocol | b. | Loop
Protocol | d. | Spanning Tree
Protocol |
|
|
40.
|
What does VTP stand for?
a. | Virtual Trunking Protocol | c. | VLAN Trunking
Protocol | b. | VLAN Transport Protocol | d. | Vehicular Transport Policy |
|